A CJ340’s cooling system is simple: a belt-driven water pump and fan, a radiator, a thermostat, a pressure cap and two main hoses. It is also asked to do a difficult job. A diesel working hard in low range moves slowly, so there is little air through the radiator, and the system has to cope with that whether the jeep is climbing a muddy lane in Wales or a sandy track in Queensland.
This guide is an overhaul plan that works in any climate. It goes through the checks in order of cost, explains how each part fails, and ends with refilling and bleeding so the job is done properly. For Australian conditions specifically, see also our Bushranger overheating guide. If you suspect the head gasket, start with our head gasket guide.
How the system should behave
A healthy cooling system warms up steadily, holds a stable temperature once the thermostat opens, and only rises slightly when working hard. The temperature gauge on an old jeep is not precise, but it is consistent: learn where your needle normally sits, and treat any change from that as information.
Diesels need to reach their operating temperature. An engine that never warms up properly burns fuel less completely, smokes, and wears faster. Removing the thermostat to “cure” overheating trades one problem for another and should not be done.
Checks in order of cost
Warning: never open the radiator cap on a hot engine. The coolant is under pressure and above its normal boiling point; releasing the cap can spray scalding coolant. Do every check below with the engine cold.
- Coolant level in the radiator, cold, and any sign of oil in it
- Pressure cap seal — perished or flattened rubber lets the system boil early
- Fan belt tension and condition — a slipping belt turns both the pump and the fan too slowly
- Hoses — soft, swollen, cracked, or a lower hose that collapses under suction
- Radiator fins — mud, grass seeds and insects packed between them block airflow
- Thermostat — test it in a pan of water before refitting
- Radiator core flow — cold patches on a warm radiator mean blocked tubes
- Fan blades — cracked or bent blades move less air and can fail violently
Radiator: clean, recore or replace
Radiators fail in two ways. From the outside, the fins pack with debris or rot away so air cannot carry heat off; from the inside, scale and corrosion block the narrow tubes so coolant cannot flow. Both produce overheating that gets worse under load.
Clean the outside with low-pressure water or air from the engine side outward, so you push debris back the way it came. For the inside, a running engine with the cap off (cold, at idle) lets you look for flow. With the engine warm and switched off, run your hand carefully across the core: cold bands mean blocked tubes.
A flushing product may restore a partly blocked radiator; a badly scaled one needs rodding or recoring by a radiator specialist. If the tanks or core are corroded through, a new radiator is often cheaper than a recore and comes back with full capacity.
Hoses and thermostat
Squeeze each hose when cold. A good hose is firm and springy. A hose that feels crunchy, very soft or swollen near its ends is failing internally. The lower hose deserves special attention: it is on the suction side of the pump, and an old one can collapse at high revs, starving the engine of coolant exactly when it needs it most. Renew the upper radiator hose and lower radiator hose together, with new clips.
Test the thermostat by suspending it in a pan of water on the stove with a thermometer. It should start to open at its marked temperature and be fully open a little above it. If it does not open, or does not close fully when cooled, replace it with one of the correct rating.
Tip: fit the thermostat the right way round, with its bleed hole or jiggle valve at the top if it has one. That lets trapped air escape and makes refilling far easier.
Coolant, refilling and bleeding
Use a good quality antifreeze mixed with clean water, even in hot climates — the inhibitors in antifreeze protect the cast iron, the aluminium head and the radiator from corrosion. A mixture of around half antifreeze and half water is a common choice; follow the product instructions and your climate. Flush the old coolant out completely rather than topping up a tired mixture.
Refill slowly with the heater control set to hot, so the heater circuit fills too. Run the engine with the cap off until the thermostat opens and the level drops, top up, and squeeze the hoses to push out trapped air. Fit the cap, warm the engine fully, let it cool, and check the level again. Repeat over the next few drives until it stays put.
If the system keeps losing coolant with no visible leak, or the coolant smells of exhaust or shows bubbles at idle, the head gasket is a suspect. Our head gasket guide explains how to prove it before stripping anything.
Driving to keep it cool
In low range on a slow climb, the engine is working hard and the jeep barely moves. Use a lower gear and higher revs rather than labouring at low revs: the pump and fan both turn faster, and the engine makes its power more easily.
On a long hot climb, stopping with the engine running at a fast idle, facing into the wind, lets the system catch up faster than switching off. Switching off a very hot engine stops the pump and can make temperatures spike in the head.
Frequently asked questions
Why does my CJ340 overheat?
The usual causes, in order of cost, are low coolant, a weak pressure cap, a slipping fan belt, perished hoses, a radiator blocked inside or out, and a stuck thermostat. A head gasket is possible but should be proven, not assumed.
Can I run a CJ340 without a thermostat?
You should not. Diesels need to reach operating temperature to burn fuel properly and wear slowly. Removing the thermostat often makes cooling worse at speed and causes smoke and wear.
Should I replace or recore a CJ340 radiator?
A scaled radiator with sound tanks can be cleaned or recored by a specialist. If the core or tanks are corroded through, a new radiator is often similar in cost and restores full cooling capacity.
What coolant should I use in a CJ340?
A quality antifreeze mixed with clean water, used year-round for its corrosion inhibitors. Flush the old coolant completely, refill with the heater on, and bleed out trapped air over several drives.
Keep yours on the road
The part this guide covers — Radiator — ships worldwide, OEM or reconditioned. Quote your chassis number (CJ3B-4 DK…) when enquiring so fitment can be checked.