Guide · GLOBAL · ~8 min read ·

CJ340 Engine and Gearbox Mounts — Vibration, Clunks and a Wandering Gear Lever

Worn CJ340 engine and gearbox mounts cause clunks, vibration, clutch judder and jumping out of gear. How to test them, what to replace and how to fit new mounts properly.

Engine and gearbox mounts are the least interesting parts of a CJ340 and among the most influential. They are rubber blocks that hold a heavy diesel and a four-speed gearbox in the chassis while letting them rock slightly as torque goes through them. When the rubber cracks, softens with oil or separates from its steel plates, the driveline moves further than it was designed to — and a surprising list of faults follows.

This guide covers the symptoms that point to mounts, how to test them in ten minutes, the knock-on problems they cause elsewhere, and how to replace them without upsetting the driveline alignment.

Symptoms that point to tired mounts

Worn mounts rarely announce themselves directly. Instead they show up as faults that get blamed on other parts. If you are chasing any of the following, check the mounts before spending money elsewhere.

Why mounts matter beyond comfort

Most of these symptoms come from one thing: the engine and gearbox rocking further than they should under torque. The gear linkage is attached to the body at one end and the gearbox at the other, so as the gearbox moves, the linkage tugs on the selectors. That is why worn mounts are one of the first things to check when a KMT90 jumps out of gear — see our gearbox guide.

The same movement upsets the clutch as it engages, producing judder that new friction material will not cure — our clutch guide lists mounts among the parts to check during any clutch job. And every clunk is a shock load through the propshaft universal joints and the transfer case.

Testing the mounts

Start with a visual check, engine off. Look at each rubber block for cracks, for rubber that has bulged or gone soft and spongy, and for separation between the rubber and its steel plates. Oil-soaked mounts are a warning in two ways: oil softens rubber quickly, and the oil is coming from a leak you also need to fix.

Next, with the engine off, use a long bar to lever gently between the engine or gearbox and the chassis near each mount. A good mount allows a little movement and springs back. A failed one lets the engine lift clear or moves with a dead, loose feel.

Warning: the classic test of watching the engine while someone engages drive against the brakes is useful but must be done carefully. The helper keeps the handbrake on and the footbrake firmly down, uses only brief, gentle throttle, and you stand to the side of the engine bay — never in front of the vehicle or near the fan and belt.

Excessive lift on one side as drive is taken up tells you which mount has failed. On the CJ340 the engine rocks around its mounts as torque is applied in one direction and the other, so check the movement in both forward and reverse.

Replacing mounts without upsetting the driveline

Replace one mount at a time where possible, supporting the engine or gearbox with a jack and a block of wood under a strong point — not under the sump, which is thin and easily damaged. Loosen the other mounts slightly so the assembly can settle, fit the new mount, then lower the weight onto it.

Tighten the mount fixings only after the full weight of the engine and gearbox is resting on all mounts. Tightening them while the engine is jacked up preloads the rubber in the wrong position and shortens its life.

Check the fan clearance to the shroud, the radiator hoses, the exhaust and the gear lever position afterwards. A sagging old mount may have put the engine slightly low or offset, and everything around it may have been adjusted to suit. Bring the clearances back to sensible figures and look for any hose or cable that is now under tension.

Tip: if one mount has failed, the others are the same age and have done the same work. Replacing the front engine mounting, the rear engine mounting and the gearbox mounting together is usually the better use of a weekend.

What vibration is normal

The XDP 4.90 is an indirect-injection diesel from an era when nobody expected diesel engines to be smooth. A healthy CJ340 shakes noticeably at idle and settles as revs rise. What should not happen is a sudden increase in vibration, a new knock as drive is taken up, or the engine visibly heaving in its bay.

If new mounts do not calm a rough idle, the cause is likely in the engine itself — an injector delivering unevenly, or a cylinder down on compression. Our injection pump guide covers the injection side.

Frequently asked questions

How do I know if my CJ340 engine mounts are worn?

Look for cracked, soft or separated rubber and oil soaking, then lever gently between engine and chassis with the engine off. A clunk on take-up, a gear lever that moves under load and heavier vibration at idle are the usual driving symptoms.

Can worn mounts make a CJ340 jump out of gear?

Yes. As the gearbox rocks on worn mounts, the gear linkage pulls on the selectors and can drag a gear out of mesh. Check mounts and linkage before assuming the KMT90 gearbox needs rebuilding.

Should I replace all the mounts together?

Usually, yes. They are the same age and have carried the same loads, and replacing them together keeps the engine and gearbox sitting at the correct height and alignment.

Is a CJ340 supposed to vibrate at idle?

Some vibration is normal for the indirect-injection XDP 4.90 diesel, and it should smooth out as revs rise. A sudden increase, a clunk or the engine visibly heaving points to failed mounts or an engine fault.

Keep yours on the road

The part this guide covers — Front engine mounting — ships worldwide, OEM or reconditioned. Quote your chassis number (CJ3B-4 DK…) when enquiring so fitment can be checked.