Oil weeping from the back of a CJ340’s front wheels is one of the most common sights on these jeeps, and one of the most misdiagnosed. The CJ340 inherited a closed-knuckle front axle from the Willys CJ-3B design: each steered wheel pivots on a large ball housing at the end of the axle, and a felt seal held by two retainer plates keeps the lubricant in and the dirt out. Felt dries, plates loosen, and the ball surface pits with rust — and then the knuckle leaks.
The fix is cheap and well within reach of a home mechanic, but it is worth confirming what is leaking before you start. This guide covers how the knuckle seals, how to separate a knuckle leak from a brake or hub leak, the replacement itself, and the lubricant debate that divides owners.
How the closed knuckle seals
On a closed-knuckle axle the steering knuckle wraps around a polished ball at the axle end, and the whole assembly is partly filled with lubricant to keep the axle shaft’s universal joint and the king pin bearings alive. Where the knuckle meets the ball, a felt ring sits behind two half-moon retainer plates bolted to the back of the knuckle. As the wheel steers, the knuckle swings around the ball and the felt wipes across its surface.
That design works well while the felt is soft and the ball is smooth. It fails when the felt hardens or shrinks with age, when the retainer bolts work loose, or when the ball surface is pitted by rust so that it acts like a file on new felt. Seal kits sold for the Dana 25 and 27 axles used under Willys CJ models typically include the felt, a gasket and the two retainer plates; one listing puts the job at one to two hours per side (Crown Automotive).
Is it really the knuckle?
Several leaks end up in the same place on a front wheel, and each needs a different fix. Before ordering anything, clean the area thoroughly, drive a short distance, and look at where the fresh fluid appears.
| Oily film on the ball and the back of the knuckle, spreading outward | Knuckle felt seal — this guide |
|---|---|
| Thin, slippery fluid on the inside of the tyre and backing plate, possibly a soft pedal | Brake wheel cylinder or hose — see our drum brake guide |
| Grease flung from the centre of the hub | Wheel bearing grease seal or hub |
| Oil near the differential housing end of the axle tube | Inner axle shaft seal at the differential, a separate part |
Warning signs that matter for safety
Warning: brake fluid on the shoes and knuckle oil on the shoes are both serious. Either one contaminates the friction material, cannot be cleaned out of it, and produces a pull under braking. If any oil has reached the inside of the drum, renew the shoes on both sides of that axle once the leak is cured — see our drum brake overhaul guide.
While the wheel is off, check the king pins for play by rocking the wheel top to bottom. Movement at the knuckle rather than at the wheel bearing means the king pin bearings need attention. King pin kits from Willys suppliers often fit Mahindra knuckles, but compare dimensions with calipers before ordering — specifications moved during the production run.
Replacing the knuckle seal
Raise and securely support the front of the jeep on axle stands, never on a jack alone. Remove the wheel. On many examples the seal can be renewed without removing the brake assembly or hub, because the retainer plates bolt to the inner face of the knuckle.
Remove the retainer plate bolts and lift away the plates and the old felt. Clean the ball thoroughly and inspect its surface. Light rust staining polishes out with fine abrasive paper; deep pitting will shred a new felt within weeks, and the ball may need to be machined or replaced.
Fit the new felt and gasket, then the retainer plates, and tighten the bolts evenly. Do not over-tighten them — one supplier specifically warns against it, because crushed felt and distorted plates leak sooner (Crown Automotive). Soaking new felt in oil before fitting helps it seal from the first turn of the wheel.
Tip: replace both sides at once. The kits are cheap, the job is the same on each side, and a jeep with one fresh seal and one tired one will be back on the stands within the year.
- Seal kit for each side: felt, gasket, two retainer plates
- Fine abrasive paper and solvent for cleaning the ball
- Fresh knuckle lubricant
- Axle stands rated for the vehicle
- Brake shoes if any contamination is found
Gear oil or knuckle grease?
Owners and suppliers disagree on what belongs inside a closed knuckle. Some Willys parts specialists use 90-weight gear oil and warn against synthetic oils because they leak more readily. Others say not to use gear oil at all and recommend a semi-fluid knuckle grease instead (Jeepster Man; Kaiser Willys).
A useful rule from the owner forums: a ball that stays dry suggests the wrong lubricant, while one that drips steadily suggests a lubricant that is too thin (jeep-cj.com). On a CJ340 used on the road with fresh felt, a semi-fluid grease is the more forgiving choice; whichever you use, do not overfill the knuckle.
Frequently asked questions
Why is oil leaking from my CJ340 front wheel?
Most often the felt seal between the steering knuckle and the axle ball has hardened or the ball surface has pitted. A leaking brake wheel cylinder, a hub grease seal or an inner axle seal can leave fluid in the same area, so clean everything and trace the fresh leak before ordering parts.
Do Willys Dana 25 knuckle seal kits fit the CJ340?
The CJ340’s front axle follows the Willys CJ-3B closed-knuckle design, and many owners use Dana 25 and 27 seal kits. Compare the felt diameter and retainer plate bolt pattern with your old parts before fitting, because Mahindra specifications changed over the years.
What lubricant goes in a closed steering knuckle?
Opinions differ. Some specialists use 90-weight gear oil; others recommend a semi-fluid knuckle grease because it leaks less through the felt. A dry ball suggests the wrong lubricant and a constantly dripping one suggests it is too thin.
Is it safe to drive with a leaking knuckle seal?
A slow weep is not an emergency, but check that no oil is reaching the brake shoes, and keep the knuckle topped up so the axle universal joint and king pin bearings are not run dry. Fix it promptly — the parts are cheap.
Sources
- Crown Automotive — Steering knuckle seal kit, Dana 25/27 (J0998445) — parts supplier listing
- Kaiser Willys — Dana 25 front axle tech and troubleshooting — parts supplier tech article
- jeep-cj.com — Closed knuckle Dana seals — owner forum
- Jeepster Man — Steering knuckle seal kit Dana 25/27 — parts supplier listing
Keep yours on the road
The part this guide covers — Steering knuckle oil seal kit — ships worldwide, OEM or reconditioned. Quote your chassis number (CJ3B-4 DK…) when enquiring so fitment can be checked.