The Peugeot XDP 4.90 in the CJ340 is an indirect-injection diesel: fuel is sprayed into a small pre-chamber in the cylinder head rather than straight onto the piston. Pre-chambers lose heat quickly when cold, so the engine relies on a glow plug in each one to get it started on a cold morning. When one or two plugs fail, the jeep starts reluctantly, rattles and smokes white for the first minute, then runs perfectly once warm — which is exactly why failed glow plugs go unnoticed for so long.
This guide shows how to test each plug with an ordinary multimeter, how to check the rest of the glow circuit, and how to replace plugs without breaking them off in the head. For the full cold-start diagnosis sequence, see our cold start guide.
Symptoms of failed glow plugs
Glow plug faults show up only when the engine is cold, and get worse as the weather does. An engine that starts promptly when warm but struggles after a cold night, and then clatters on fewer than four cylinders for the first minute, is the classic picture.
- Long cranking before the engine fires on cold mornings
- Rough running and a misfire for the first minute after a cold start
- White or blue-white smoke at cold start that clears as the engine warms
- Starts normally once warm or in summer
- Glow warning lamp behaving differently from usual, on models that have one
Testing each plug with a multimeter
Disconnect the battery. Remove the nut that holds the bus bar or feed wire to each glow plug and lift the bar clear, so each plug can be tested on its own.
Set the multimeter to its lowest resistance range. Put one probe on the plug’s terminal and the other on a clean earth on the engine. A working plug shows a very low resistance — typically around an ohm or less. A plug that shows no continuity at all is open-circuit and dead.
Compare all four plugs. Because healthy resistances are so low, a cheap meter cannot tell good from tired reliably; the clearest result is the difference between a plug that conducts and one that does not. Where you have a clamp-type ammeter, measuring the current each plug draws with the glow circuit switched on is a better test of a weak plug.
Tip: test the plugs on a cold engine before a winter, not on the morning it refuses to start. A plug that has failed open will not recover, and replacing them in the warmth of an autumn afternoon is far easier.
Check the rest of the glow circuit
Four good plugs will not help if the current cannot reach them. With the bus bar refitted and the glow circuit switched on, measure the voltage at the bus bar. It should be close to battery voltage. If it is low or absent, work back towards the battery through the glow relay or timer, its fuses and the dash switch or key position that operates it — CJ340s and their export versions differ here, so trace your own wiring.
Clean the bus bar and the plug terminals. Corrosion under the nuts adds resistance across a circuit that carries heavy current, and the result is plugs that only get warm rather than hot.
Glow plugs draw a lot of current. A battery that is merely tired may still crank the engine in summer but cannot run the glow circuit and the starter on a cold morning. Test the battery properly as part of any glow plug diagnosis — see our starter and battery guide.
Replacing glow plugs without snapping them
Old glow plugs can seize in the head, and a plug that snaps is a cylinder-head-off job to extract. The aim is to remove them gently, with patience rather than force.
Clean around each plug with a brush and compressed air so dirt cannot fall into the pre-chamber. Apply penetrating oil and leave it overnight if you can. Run the engine to normal temperature before removal; the warm aluminium head expands slightly and releases the threads more easily.
Use a deep socket that fits squarely on the plug’s hex, and turn steadily. If a plug resists, do not lean on it — work it back and forth a fraction of a turn at a time with more penetrating oil. Warning: a plug that suddenly feels soft has probably sheared. Stop and get advice before you damage the threads in the head.
Fit new plugs by hand first, so the threads cannot cross. General references for the Peugeot XD engine family give a tightening torque in the range of 20–40 Nm (motor-car.net); use the figure in your workshop manual and err on the gentle side. Over-tightening distorts the plug body and can break the tip off inside the pre-chamber.
Which plugs fit
The XDP 4.90 shares its basic design with the Peugeot XD90 2.1-litre diesel used in the Peugeot 504 and other vehicles, and parts suppliers list glow plugs for the XD 4.90 under those applications (Alepoc). General XD-family references list Bosch 0 250 201 019, Beru 636 MJ, Champion CH68 and Lucas/CAV HDS337 (motor-car.net).
Treat those numbers as a starting point, not a guarantee. Before fitting, compare the new plug with an old one: thread size and length, the reach of the heating tip and the terminal type must all match. A tip that sits too far into the pre-chamber can be damaged; one that is too short will not heat the chamber properly.
Replace all four plugs at the same time. They are the same age, and a single new plug alongside three tired ones still leaves the engine starting on fewer than four cylinders.
Frequently asked questions
How do I test CJ340 glow plugs?
Disconnect the battery and the bus bar, then measure resistance from each plug terminal to engine earth. A working plug shows very low resistance, typically around an ohm or less; a plug with no continuity has failed. A clamp ammeter measuring current draw is a better test for weak plugs.
What glow plugs fit the Peugeot XDP 4.90?
Suppliers list glow plugs for the XD 4.90 under Peugeot 504 2.1 diesel applications, and XD-family references include Bosch 0 250 201 019 and Champion CH68. Compare thread length and tip reach with your old plug before fitting.
Should I replace all four glow plugs?
Yes. They are the same age, and replacing only the failed one leaves the engine likely to lose another plug soon. Cold starts depend on all four pre-chambers heating properly.
What if a glow plug snaps in the head?
A sheared glow plug usually means removing the cylinder head to extract it. Avoid it by removing plugs from a warm engine after soaking them in penetrating oil, and by working them gently rather than forcing them.
Sources
- motor-car.net — PSA XD Indenor engine (1963–1992) — engine reference, XD family
- Alepoc — Set of 4 glow plugs for Peugeot 504 D 2.1, XD 4.90 — parts supplier listing
Keep yours on the road
OEM and reconditioned CJ340 parts ship worldwide. Explore the fan site, regional guides, and owner community.