Not every CJ340 fault is a gearbox or an injection pump. Some of the most annoying are small: a speedometer needle that bounces or sits at zero, wipers that stop wherever they please, and an ignition switch that does strange things. These are also the faults that fail roadworthiness inspections in the UK, Europe and Australia, because speed indication, wipers and controls all appear on the checklist.
This guide covers all three. None needs special tools beyond a multimeter, and each one usually costs far less than the time spent living with it.
Speedometer: bouncing, ticking or dead
The CJ340 speedometer is mechanical. A cable inside an outer sleeve runs from a drive gear on the transfer case up to the back of the instrument, and the needle follows the cable’s rotation. Almost every speedometer fault comes from that cable or its drive.
| Needle bounces or swings | Dry or kinked cable, or a tight bend in the routing |
|---|---|
| Ticking or squealing behind the dash | Dry cable or a worn instrument bush |
| Needle stays at zero, cable turns | Fault in the instrument head |
| Needle stays at zero, cable does not turn | Broken inner cable or stripped drive gear |
Fixing the speedometer cable
Disconnect the cable at the back of the instrument and pull the inner out. If it comes out in two pieces, it has broken; if it comes out whole, check whether it turns when the jeep is pushed or driven slowly with the cable disconnected at the top. If the inner does not turn at all, the drive gear at the transfer case may be stripped.
Lubricate a sound inner cable lightly with a cable grease, keeping the top 15 cm or so clean so grease cannot work up into the instrument. Re-route the outer with gentle curves; a tight bend or a cable tie pulled too hard will make the needle bounce again within weeks.
Speedometer cable routing on export dashboards differs from Willys practice, so a CJ-3B cable may be the wrong length. Measure your old cable end to end when ordering, or use a Mahindra-specification speedo cable.
Tip: changing tyre size changes the speedometer reading. A CJ340 on non-standard tyres may read wrongly even with a perfect cable — see our 700×16 tyre guide.
Wipers that won’t work or won’t park
Wiper faults split into electrical and mechanical. Start with the electrical side because it is quicker to test. With the switch on, check for battery voltage at the motor’s feed wire and for a good earth. Many old wiper motors earth through their mounting, and corrosion there is a common cause of a slow or dead motor.
If the motor runs when fed directly from the battery but not from the switch, the switch or its wiring is at fault. If it runs but the blades do not move, the linkage or a stripped gear inside the motor is at fault. If the blades stop wherever you switch off, the park switch inside the motor is not working — that circuit brings the blades back to rest after the switch is turned off.
Seized linkages overload the motor and burn it out, so free and grease the pivots whenever you have the motor off. If the motor itself is worn or burnt, a replacement wiper motor is usually the practical fix.
Left-hand-drive and right-hand-drive CJ340s park their wipers on opposite sides. If you are ordering parts for a converted or imported jeep, specify which you have.
Ignition switch faults
The ignition switch on a CJ340 does more than start the engine. On a diesel it also feeds the stop solenoid on the injection pump, which must stay energised for fuel to flow. A switch with worn internal contacts can therefore produce some alarming faults.
- The engine cuts out abruptly while driving, then restarts — the switch has briefly broken the feed to the stop solenoid
- Dashboard warning lights flicker when the key is touched or the jeep hits a bump
- Nothing happens when the key is turned to start, though the battery is good
- The key is stiff, sticks, or turns without operating the switch
Testing and replacing the switch
With the battery connected and a multimeter on each output terminal of the switch, turn the key through its positions. Each terminal should show battery voltage in the right positions and hold it steadily. Wiggle the key gently in each position: any flicker in the reading means worn contacts.
Before blaming the switch for a cutting-out fault, check the stop solenoid’s own wiring and connector, because a loose connection there gives the same symptom. Our electrical charging guide also explains how a failing charging system can let the stop solenoid drop out.
Warning: disconnect the battery before removing the switch from the dash. Several wires behind it are live at all times and will short against the dash panel. Label every wire before disconnecting it, then fit the new ignition switch and reconnect in the same order.
Frequently asked questions
Why does my CJ340 speedometer needle bounce?
Usually a dry or kinked speedometer cable, or a tight bend in its routing. Remove the inner cable, lubricate it lightly while keeping the top end clean, and re-route the outer with gentle curves.
Why won’t my CJ340 wipers park?
The park switch inside the wiper motor returns the blades to rest after you switch off. If the blades stop wherever you switch them off, the park switch or its wiring has failed. Check the motor earth and feed first.
Why does my CJ340 cut out while driving and then restart?
A worn ignition switch can briefly break the feed to the injection pump stop solenoid, which shuts off fuel. Check the switch with a multimeter while gently wiggling the key, and inspect the stop solenoid wiring.
Will a Willys CJ-3B speedometer cable fit a CJ340?
Not reliably. Routing on export CJ340 dashboards differs from Willys practice, so the length may be wrong. Measure your old cable or order a Mahindra-specification cable.
Keep yours on the road
The part this guide covers — Speedo cable — ships worldwide, OEM or reconditioned. Quote your chassis number (CJ3B-4 DK…) when enquiring so fitment can be checked.